Vapour control for tank terminals and storage facilities.

Filling, emptying and breathing cycles release vapours from crude, fuels, chemicals and specialty liquids. BM Process engineers vapour capture, recovery and treatment that protects product, people and permits.

100+

Projects delivered


20+

Years senior experience


2

Strategic partners


1:1

Senior contact, no layers

Technology-independent assessment

ATEX-aware engineering

From concept to optimisation

Where do terminal
emissions arise?

01
Tank breathing

Thermal and pressure variations in fixed-roof tanks

Learn more

02
Filling & emptying

Vapour displacement during product transfers

Learn more

03
Loading bays

Truck, rail and barge loading operations

Learn more

04
VOCs & BTX

Gasoline, solvents, aromatics and specialty chemicals

Learn more

05
Sulphur compounds

H₂S from sour crude and distillates

Learn more

06
Blanketing gas

Nitrogen and inert vents carrying VOCs and odour

Learn more

01

Environmental regulations

EU VOC and BAT limits for storage and transfer of liquids


02

Odour management

Breathing losses cause odour near ports and populated areas


03

Product loss prevention

Recovered vapours are product that would otherwise be lost


04

Worker safety & ATEX

Explosive and toxic vapours require controlled systems


05

Community & ESG pressure

Environmental performance affects licences and reputation

Why emissions must be managed

Every vented vapour is lost product.

Terminal emissions depend on product mix, throughput and tank configuration. We combine knowledge of storage operations and abatement technology to select the solution that fits your terminal and its permit.

Technologies

Emission-control technologies we engineer and integrate.

Our strength lies in combining tank-storage operations knowledge with full-scope engineering — process, piping, mechanical, E&I and automation.

Treatment capacity is matched to product mix, transfer rates and tank configuration.

Smart integration

Capture, recover, treat. Always a holistic approach.

Vapour balancing

Product mix

Transfer rates

ATEX zoning

Recovery value

Permit limits

Engineering first, emissions controlled

We focus on emission control, process engineering and safety studies for tank terminal operators.


01

Consultancy & compliance

Advice studies on limits, permits and BAT.


02

Pre-engineering

Feasibility studies and technology comparison.


03

Basic & detailed engineering

Process, piping, mechanical and E&I design.


04

Safety studies

ATEX zoning, HAZOP and interlock design.


05

Owner’s engineering

Project support from tender to commissioning.

Don’t see your process here?
Emission challenges rarely fit neat categories. Start from the problem — we’ll map the route.

Discuss your process

Industries we serve

One engineering partner across every emission-heavy sector — from coating lines and refineries to biogas plants, recycling halls and commercial kitchens.

Adhesives, Coating & Surface Treatment
VOC capture, solvent recovery and abatement for coating and laminating lines.

Explore sector

Petrochemical Industry
VRU, enclosed flares, RTO / CatOx and scrubbers for hydrocarbon streams.

Explore sector

Automotive
Paint booths, drying ovens, sealants and engine test cell exhaust.

Explore sector

Tank Storage
Vapour recovery, breathing losses and loading bay emissions.

Explore sector

Wastewater Treatment
Biofilters, scrubbers and carbon polishing for treatment plants.

Explore sector

Biogas & Renewable Energies
Gas upgrading, digester off-gas and CHP exhaust treatment.

Explore sector

Waste Treatment & Recycling
Sorting halls, MBT, composting and e-waste — odour, dust and VOC.

Explore sector

Food & Beverage
Odour, grease and VOC treatment with UV, plasma, RTO and scrubbers.

Explore sector

Project lifecycle

Independent engineering, practical delivery

One partner across the complete project lifecycle. BM Process connects process knowledge with proven emission-control technologies — helping you challenge assumptions, compare lifecycle costs and build a technically defensible investment case.

01
Assessment

Site review, data gap analysis and technology screening

02
Concept

Basis of design, CAPEX/OPEX comparison and roadmap

03
Execution

Vendor evaluation, interface coordination and support

04
Optimisation

Troubleshooting, energy review and system improvement

Engagements can start at any phase — not every assignment includes every stage.

Technology partner

Krantz Clean Air Solutions

BM Process supports Krantz thermal clean-air solutions in the Netherlands and Belgium, backed by extensive industrial engineering experience.

Engineering & local support by BM Process

Proven clean-air technology
Oxidation systems and heat integration for industrial exhaust air.
Regenerative – RTO

High thermal efficiency for continuous processes.

Recuperative

Direct heat exchange for compact installations.

Catalytic

Lower operating temperature, reduced fuel demand.

Heat recovery

Energy integration in the total plant heat balance.

Selection and sizing alwaysfollow your emission profile.
ATEX aware engineering, by design

ATEX & Safety

VOC control and explosion safety must be engineered together.

Safe operation requires control of VOC concentration together with suitable ventilation, ATEX zoning, ignition-source control, monitoring, interlocks and explosion-protection measures.

VOC concentration

Kept below safe limits

Ventilation

Dilution and capture

ATEX zoning

Classified areas

Ignition control

Equipment selection

Monitoring & interlocks

Detect and respond

Explosion protection

Mitigation measures

FAQ

Questions we often discuss with plant teams

The first technical conversation can usually identify the most important data gaps and feasible pathways.

Still have questions about your process?

Share the application and your main concern — we’ll map the most useful next step together.

Which emissions occur at tank terminals?

VOCs from gasoline, solvents and chemicals, BTX aromatics, sulphur compounds such as H2S from sour products, odorous off-gas from loading operations and inert blanketing gas carrying vapours.

Should vapours be recovered or destroyed?

Recovery suits high-value hydrocarbon vapours at sufficient concentration. Mixed, lean or low-value streams are often better treated by thermal oxidation or activated carbon.

How is ATEX handled in vapour collection systems?

Vapour collection lines are designed with flame arresters, concentration monitoring, pressure and vacuum protection, and interlocks, with zoning defined in the ATEX assessment.

Can you upgrade an existing VRU?

Yes. We assess capacity, recovery efficiency and energy use against the current product mix and permit, and propose upgrades or additional polishing stages.

Contact

Start with your process

Not sure which VOC solution fits? Share the application and your main concern. We’ll use the first discussion to understand the process, available data and the most useful next step.

Broekstraat 6, 5292 ND Gemonde, NL

hello@bmprocess.nl

+31 6 42173663

Request a technical discussion

Response within one working day

Great! We’ve received your information.

Contact

Trusted by Industry Leaders

Not sure where to start? Talk to an engineer directly.